中国工业强基重点产品，中国工信部传感器一条龙应用计划示范企业（米朗科技）
中国工信部高精度传感器一条龙应用计划示范项目,24小时服务热线：19926637026
中国工业强基重点产品，中国工信部传感器一条龙应用计划示范企业（米朗科技）
中国工信部高精度传感器一条龙应用计划示范项目,24小时服务热线：19926637026
深圳市米朗科技有限公司
电话：19926637026（向小姐）
18988775309（单先生）
传真：0755-81738623
邮箱：2355721211@qq.com
地址：广东省深圳市光明区马田街道中粮云景广场第一栋29层米朗科技
MR-2232 (4L)
稀油电动润滑油泵微电脑型 Self-control electric oil lubrication pump
技术参数Technical Parameters
型号 Model | 电压频率 Voltage | 额定转速 Rated ritary Speed | 功率 Power | 电流 Current(A) | 额定压力 Rated pressure kgf/cm2 | Z大压力 Max pressure kgf/cm2 | 容积 Volume | 吐出量 Discharge capacity ml/min | 使用油粘度 Rated pressure kgf/cm2 | 备注 Remarks |
MR-2232-400TAB | 220V 50/60HZ | 2400 | 18W | 0.12 | 18 | 35 | 4L | 150-200CC/min | 30-1000 | MR-2231代表 电压110V MR-2232代表 电压220V |
MR-2232-400XAB | 220V 50/60HZ | |||||||||
MR-2232-410XAB | 220V 50/60HZ |
*型号带T为抵抗式，带X为容积式,带A为罩极电机,
*Mode name with " T" is resistant, mode name with “X” is volumetric,mode name with “A” is s h a d e - p o l e m o t o
使用方法Method ofuse
1 .工作时间：请长按键,见数字在跳动时，松开S E T键，按键SET ▲ ▼ 设定个位数;按下SET键，按▲ ▼ 键设定十位数；再按下
SET键，一下SET键设定百位数(1-999秒)。
2.间歇时间：请长按SET键，见另一个显示屏数字在跳动时，松开SET键，按键▲ ▼ 键设置个位数；按一下SET键，同时按键▲
▼约2秒，间歇时间可分秒转换 ( 1 -9 9 9分或1 - 9 9 9秒）。
3.RST 键 按住此键可重新润滑或清除异常报警。
4.电路电源接通后系统属于给油状态，并进入LUB、 INT循环，
供油时左边LUB绿灯亮，间歇时右边INT红灯亮。
5.ERO 闪烁时代表油量不足，ERP闪烁时代表压力异常。
6.数显中框内设有断电记忆功能，打开小开关﹄进入断电记忆。
关闭小开关﹄，断电记忆停止。
7.数显框内设有按键锁功能﹄，可根据自行需要设置好时间后是
否需锁住设置按键。
（可根据客户需要定做专属润滑方案）
1.Working time: press and hold the SET button, release it when the numbers jump, then press ▲ ▼ to set unit digit; and press the button of SET again, to set ten
digit with pressing ▲ ▼; press SET to hundreds digit(1~999 seconds).
2.Interval time: press and hold the SET button, release it when the numbers in other Display screen jump, then press ▲ ▼ to set unit digit; and press the button of
SET for two seconds, the interval time can shift between minutes and second(1~999 minutes or 1~999 seconds).
3.RST: Press and hold this key to relubricate or clear the abnormal alarm.
4.After the circuit power is turned on, the system belongs to the oil supply state, and enters the LUB, INT cycle. When the fuel is supply , the left LUB green light is
on, the right INT red light is on when the system is on rest.
5.When the ERO flashes, it means that the amount of oil is insufficient, and when the ERP flashes, it means that the pressure is abnormal.
6.There is no power-off memory function in the digital display box, and a small switch is turned on to enter the power-off memory. Turn off the small switch, and the
power off memory stops.
7.There is a key lock function in the digital display box. You can lock the set button after setting the time according to your needs.
(The lubrication program Can be customized according to customers’ requirements)
